APRS Track Direct

My position About ☰

reset

WG4USA-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WG4USA-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	DigiRpt*	Temp*
1786727100	4 Pkts	4 Pkts	1 Pkts	17 C
1786723500	0 Pkts	0 Pkts	0 Pkts	17 C
1786719899	0 Pkts	0 Pkts	0 Pkts	17 C
1786716299	0 Pkts	0 Pkts	0 Pkts	16 C
1786712699	11 Pkts	11 Pkts	7 Pkts	17 C
1786709100	11 Pkts	11 Pkts	7 Pkts	17 C
1786705500	14 Pkts	14 Pkts	6 Pkts	17 C
1786701900	9 Pkts	9 Pkts	7 Pkts	17 C
1786698299	21 Pkts	20 Pkts	14 Pkts	17 C
1786694699	20 Pkts	20 Pkts	11 Pkts	17 C
1786691099	37 Pkts	35 Pkts	28 Pkts	16 C
1786687499	34 Pkts	34 Pkts	22 Pkts	17 C
1786683899	24 Pkts	24 Pkts	18 Pkts	17 C
1786680299	38 Pkts	37 Pkts	21 Pkts	16 C
1786676699	53 Pkts	53 Pkts	33 Pkts	17 C
1786673099	39 Pkts	39 Pkts	26 Pkts	17 C
1786669499	30 Pkts	29 Pkts	19 Pkts	17 C
1786665899	9 Pkts	8 Pkts	6 Pkts	17 C
1786662299	7 Pkts	6 Pkts	5 Pkts	17 C
1786658699	42 Pkts	42 Pkts	25 Pkts	17 C
1786655099	2 Pkts	2 Pkts	2 Pkts	16 C
1786651499	5 Pkts	5 Pkts	4 Pkts	17 C
1786647899	0 Pkts	0 Pkts	0 Pkts	17 C
1786644300	2 Pkts	2 Pkts	1 Pkts	17 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)