APRS Track Direct

My position About ☰

reset

SR8LWA Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR8LWA. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*	Value5*
1732569978	14.1 Volt	460 Pkt	120 Pkt	60 Pcnt	-64
1732566374	14.18 Volt	480 Pkt	140 Pkt	61 Pcnt	-64
1732562771	14.1 Volt	600 Pkt	140 Pkt	66 Pcnt	-64
1732559168	14.1 Volt	630 Pkt	170 Pkt	70 Pcnt	-64
1732555565	14.18 Volt	540 Pkt	120 Pkt	66 Pcnt	-64
1732551961	14.1 Volt	480 Pkt	100 Pkt	60 Pcnt	-64
1732548357	14.1 Volt	490 Pkt	110 Pkt	59 Pcnt	-64
1732544754	14.18 Volt	400 Pkt	90 Pkt	56 Pcnt	-64
1732541151	14.18 Volt	450 Pkt	90 Pkt	64 Pcnt	-64
1732537547	14.18 Volt	340 Pkt	80 Pkt	51 Pcnt	-64
1732533944	14.18 Volt	370 Pkt	100 Pkt	54 Pcnt	-64
1732530340	14.1 Volt	420 Pkt	120 Pkt	56 Pcnt	-64
1732526737	14.1 Volt	410 Pkt	100 Pkt	54 Pcnt	-64
1732523133	14.18 Volt	410 Pkt	100 Pkt	55 Pcnt	-64
1732519530	13.95 Volt	560 Pkt	190 Pkt	61 Pcnt	-64
1732515927	14.1 Volt	490 Pkt	120 Pkt	64 Pcnt	-64
1732512323	14.18 Volt	410 Pkt	110 Pkt	67 Pcnt	-64
1732508719	14.18 Volt	450 Pkt	130 Pkt	67 Pcnt	-64
1732505116	13.95 Volt	470 Pkt	120 Pkt	67 Pcnt	-64
1732501513	13.88 Volt	480 Pkt	120 Pkt	72 Pcnt	-64

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Value5: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)