APRS Track Direct

My position About ☰

reset

YM7KK Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YM7KK. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1732228339	13.28 Volt	160 Pkt	20 Pkt	55 Pcnt
1732228040	13.28 Volt	150 Pkt	20 Pkt	55 Pcnt
1732228039	13.28 Volt	150 Pkt	20 Pkt	55 Pcnt
1732227739	13.28 Volt	160 Pkt	20 Pkt	55 Pcnt
1732227440	13.28 Volt	150 Pkt	20 Pkt	52 Pcnt
1732227439	13.28 Volt	150 Pkt	20 Pkt	52 Pcnt
1732227139	13.28 Volt	150 Pkt	20 Pkt	53 Pcnt
1732226840	13.28 Volt	150 Pkt	20 Pkt	52 Pcnt
1732226839	13.28 Volt	150 Pkt	20 Pkt	52 Pcnt
1732226539	13.28 Volt	160 Pkt	20 Pkt	53 Pcnt
1732226239	13.28 Volt	150 Pkt	20 Pkt	52 Pcnt
1732226239	13.28 Volt	150 Pkt	20 Pkt	52 Pcnt
1732225939	13.28 Volt	160 Pkt	20 Pkt	52 Pcnt
1732225640	13.28 Volt	150 Pkt	20 Pkt	49 Pcnt
1732225639	13.28 Volt	150 Pkt	20 Pkt	49 Pcnt
1732225339	13.28 Volt	160 Pkt	20 Pkt	50 Pcnt
1732225039	13.28 Volt	160 Pkt	20 Pkt	51 Pcnt
1732225039	13.28 Volt	160 Pkt	20 Pkt	51 Pcnt
1732224739	13.28 Volt	160 Pkt	20 Pkt	51 Pcnt
1732224439	13.28 Volt	160 Pkt	20 Pkt	50 Pcnt
1732224439	13.28 Volt	160 Pkt	20 Pkt	50 Pcnt
1732224139	13.28 Volt	160 Pkt	20 Pkt	50 Pcnt
1732223840	13.28 Volt	160 Pkt	30 Pkt	49 Pcnt
1732223839	13.28 Volt	160 Pkt	30 Pkt	49 Pcnt
1732223539	13.28 Volt	150 Pkt	20 Pkt	48 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)