APRS Track Direct

My position About ☰

reset

WCSAR-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WCSAR-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Vin*	Rx1h*	Dg1h*
1732225353	13.65 Volt	10 Pkt	10 Pkt
1732223550	13.65 Volt	10 Pkt	10 Pkt
1732222650	13.65 Volt	0 Pkt	0 Pkt
1732222088	13.65 Volt	0 Pkt	0 Pkt
1732220848	13.65 Volt	0 Pkt	0 Pkt
1732219046	13.65 Volt	10 Pkt	10 Pkt
1732217244	13.65 Volt	10 Pkt	10 Pkt
1732215443	13.65 Volt	10 Pkt	10 Pkt
1732213641	13.65 Volt	10 Pkt	10 Pkt
1732212740	13.65 Volt	10 Pkt	10 Pkt
1732211839	13.65 Volt	10 Pkt	10 Pkt
1732210938	13.65 Volt	10 Pkt	10 Pkt
1732209137	13.65 Volt	10 Pkt	10 Pkt
1732208236	13.65 Volt	10 Pkt	10 Pkt
1732207335	13.65 Volt	10 Pkt	10 Pkt
1732201930	13.65 Volt	10 Pkt	10 Pkt
1732201029	13.65 Volt	10 Pkt	10 Pkt
1732200128	13.65 Volt	10 Pkt	10 Pkt
1732199227	13.65 Volt	0 Pkt	0 Pkt
1732198326	13.65 Volt	0 Pkt	0 Pkt
1732197426	13.65 Volt	0 Pkt	0 Pkt
1732196525	13.65 Volt	0 Pkt	0 Pkt
1732195624	13.65 Volt	10 Pkt	10 Pkt
1732194723	13.65 Volt	10 Pkt	10 Pkt
1732193822	13.65 Volt	10 Pkt	10 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Temp: 0, 0.5, -64

I1: 0, 19.5, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)