APRS Track Direct

My position About ☰

reset

LW5DR Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LW5DR. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1786741292	6 Pkt	-59 dBm	5.33 V
1786739768	3 Pkt	-60 dBm	5.33 V
1786738247	12 Pkt	-60 dBm	5.33 V
1786736725	6 Pkt	-61 dBm	5.33 V
1786735202	0 Pkt	-61 dBm	5.33 V
1786733609	19 Pkt	-60 dBm	5.33 V
1786732090	22 Pkt	-60 dBm	5.33 V
1786730563	7 Pkt	-61 dBm	5.33 V
1786729041	65 Pkt	-60 dBm	5.33 V
1786727515	16 Pkt	-61 dBm	5.33 V
1786725988	7 Pkt	-62 dBm	5.31 V
1786724465	6 Pkt	-62 dBm	5.33 V
1786722942	65 Pkt	-62 dBm	5.33 V
1786721415	9 Pkt	-62 dBm	5.33 V
1786719892	12 Pkt	-61 dBm	5.33 V
1786718369	87 Pkt	-62 dBm	5.33 V
1786716840	80 Pkt	-61 dBm	5.33 V
1786715312	20 Pkt	-62 dBm	5.33 V
1786713788	31 Pkt	-60 dBm	5.33 V
1786712263	48 Pkt	-60 dBm	5.33 V
1786710743	6 Pkt	-61 dBm	5.33 V
1786709205	3 Pkt	-60 dBm	5.33 V
1786707683	6 Pkt	-63 dBm	5.33 V
1786706161	8 Pkt	-60 dBm	5.33 V
1786704638	20 Pkt	-61 dBm	5.33 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)