APRS Track Direct

My position About ☰

reset

FW0727 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object FW0727. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Ground*	Inside*	PV_P*	PV_U*	Bat*
1758176783	18.5 degC	17 degC	0 W	5.75 V	4.24 V
1758172769	18.5 degC	13.5 degC	0.78 W	4.23 V	4.21 V
1758170105	18 degC	12 degC	0.03 W	4.83 V	4.16 V
1758163787	18.5 degC	12 degC	0 W	0.15 V	4.12 V
1758160771	18.5 degC	12 degC	0 W	0.15 V	4.13 V
1758157776	18.5 degC	12.5 degC	0 W	0.15 V	4.13 V
1758154123	18.5 degC	13 degC	0 W	0.15 V	4.14 V
1758153439	18.5 degC	13 degC	0 W	0.15 V	4.14 V
1758152426	18.5 degC	13 degC	0 W	0.15 V	4.17 V
1758151388	18.5 degC	13.5 degC	0 W	0.15 V	4.14 V
1758149382	18.5 degC	13.5 degC	0 W	0.15 V	4.14 V
1758149028	18.5 degC	13.5 degC	0 W	0.15 V	4.14 V
1758144054	19 degC	14.5 degC	0 W	0.15 V	4.15 V
1758142049	19 degC	15 degC	0 W	0.15 V	4.16 V
1758139368	19 degC	16 degC	0 W	0.13 V	4.17 V
1758138683	19.5 degC	16 degC	0 W	0.13 V	4.17 V
1758137339	19.5 degC	16 degC	0 W	0.15 V	4.17 V
1758136326	19.5 degC	16.5 degC	0 W	0.13 V	4.18 V
1758135640	19.5 degC	16.5 degC	0 W	0.13 V	4.17 V

*Used Equation Coefficients:

Ground: 0, 0.5, -25

Inside: 0, 0.5, -25

PV_P: 0, 0.01, 0

PV_U: 0, 0.025, 0

Bat: 0, 0.01, 2.5

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)