APRS Track Direct

My position About ☰

reset

E24MSQ-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E24MSQ-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1782546340	0 Pkt	-59 dBm	14.56 V
1782545416	0 Pkt	-58 dBm	14.17 V
1782544492	0 Pkt	-58 dBm	15.3 V
1782543567	0 Pkt	-60 dBm	14.07 V
1782542643	0 Pkt	-58 dBm	14.17 V
1782541718	0 Pkt	-56 dBm	14.85 V
1782540794	0 Pkt	-60 dBm	15.44 V
1782539869	0 Pkt	-57 dBm	14.19 V
1782538944	0 Pkt	-60 dBm	15.03 V
1782538020	0 Pkt	-60 dBm	15.16 V
1782537095	0 Pkt	-59 dBm	13.97 V
1782536171	0 Pkt	-60 dBm	13.9 V
1782535246	0 Pkt	-60 dBm	13.8 V
1782534322	0 Pkt	-59 dBm	13.86 V
1782533397	0 Pkt	-60 dBm	13.95 V
1782532473	0 Pkt	-60 dBm	13.62 V
1782531548	0 Pkt	-58 dBm	13.62 V
1782530624	0 Pkt	-59 dBm	13.66 V
1782529699	0 Pkt	-60 dBm	13.62 V
1782528775	0 Pkt	-59 dBm	13.6 V
1782527850	0 Pkt	-58 dBm	13.64 V
1782526926	3 Pkt	-57 dBm	13.35 V
1782526001	0 Pkt	-58 dBm	13.47 V
1782525077	0 Pkt	-58 dBm	13.47 V
1782524152	0 Pkt	-56 dBm	13.45 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)