APRS Track Direct

My position About ☰

reset

E24LIW-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E24LIW-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1786811508	0 Pkt	-66 dBm	0.16 V
1786810886	0 Pkt	-65 dBm	0.16 V
1786810194	0 Pkt	-65 dBm	0.18 V
1786809572	0 Pkt	-65 dBm	0.18 V
1786808950	0 Pkt	-64 dBm	0.21 V
1786808328	0 Pkt	-64 dBm	0.18 V
1786807706	0 Pkt	-63 dBm	0.18 V
1786807084	0 Pkt	-64 dBm	0.21 V
1786806462	0 Pkt	-63 dBm	0.16 V
1786805840	0 Pkt	-63 dBm	0.16 V
1786805218	0 Pkt	-63 dBm	0.21 V
1786804596	0 Pkt	-64 dBm	0.21 V
1786803974	0 Pkt	-63 dBm	0.18 V
1786803352	2 Pkt	-65 dBm	0.16 V
1786802730	0 Pkt	-65 dBm	0.21 V
1786802108	0 Pkt	-65 dBm	0.18 V
1786801486	0 Pkt	-65 dBm	0.18 V
1786800864	0 Pkt	-64 dBm	0.21 V
1786800242	2 Pkt	-65 dBm	0.21 V
1786799620	0 Pkt	-66 dBm	0.21 V
1786798928	0 Pkt	-65 dBm	0.16 V
1786798306	4 Pkt	-68 dBm	0.18 V
1786797684	0 Pkt	-66 dBm	0.21 V
1786797061	0 Pkt	-65 dBm	0.18 V
1786796439	0 Pkt	-65 dBm	0.18 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)