APRS Track Direct

My position About ☰

reset

OE5XDO-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE5XDO-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	U-Netz*	U-Akku*	STBY*	BUSY*
1732293925	13.43 V	13.43 V	8 cnt	16 cnt
1732293625	13.44 V	13.43 V	8 cnt	16 cnt
1732293326	13.44 V	13.44 V	7 cnt	15 cnt
1732293026	13.44 V	13.44 V	7 cnt	15 cnt
1732292727	13.41 V	13.43 V	7 cnt	15 cnt
1732292427	13.43 V	13.43 V	7 cnt	15 cnt
1732292127	13.41 V	13.41 V	7 cnt	15 cnt
1732291828	13.43 V	13.43 V	7 cnt	15 cnt
1732291531	13.43 V	13.43 V	7 cnt	15 cnt
1732291229	13.43 V	13.43 V	7 cnt	15 cnt
1732290929	13.44 V	13.44 V	7 cnt	15 cnt
1732290629	13.44 V	13.44 V	7 cnt	15 cnt
1732290330	13.43 V	13.44 V	7 cnt	15 cnt
1732290031	13.43 V	13.43 V	7 cnt	15 cnt
1732289730	13.41 V	13.43 V	7 cnt	15 cnt
1732289431	13.44 V	13.43 V	7 cnt	15 cnt
1732289131	13.44 V	13.43 V	7 cnt	15 cnt
1732288832	13.43 V	13.43 V	7 cnt	15 cnt
1732288533	13.41 V	13.43 V	7 cnt	15 cnt
1732288232	13.44 V	13.43 V	7 cnt	15 cnt
1732287933	13.43 V	13.43 V	7 cnt	15 cnt
1732287636	13.41 V	13.41 V	7 cnt	15 cnt
1732287334	13.41 V	13.41 V	6 cnt	14 cnt
1732287034	13.44 V	13.43 V	6 cnt	14 cnt
1732286734	13.41 V	13.41 V	6 cnt	14 cnt

*Used Equation Coefficients:

U-Netz: 0, 0.01, 0

U-Akku: 0, 0.01, 0

STBY: 0, 1, 0

BUSY: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)