APRS Track Direct

My position About ☰

reset

TA3TX-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA3TX-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1762248288	4 Pkt	-26 dBm	21 V
1762247425	11 Pkt	-27 dBm	21 V
1762246561	11 Pkt	-26 dBm	21 V
1762245698	8 Pkt	-26 dBm	21 V
1762244834	11 Pkt	-28 dBm	21 V
1762243969	17 Pkt	-26 dBm	21 V
1762243105	10 Pkt	-26 dBm	21 V
1762242241	21 Pkt	-26 dBm	21 V
1762241373	16 Pkt	-27 dBm	21 V
1762240507	7 Pkt	-26 dBm	21 V
1762239643	10 Pkt	-27 dBm	21 V
1762238780	9 Pkt	-28 dBm	21 V
1762237915	9 Pkt	-26 dBm	21 V
1762237053	12 Pkt	-26 dBm	21 V
1762236189	9 Pkt	-26 dBm	21 V
1762235325	9 Pkt	-26 dBm	21 V
1762234461	8 Pkt	-26 dBm	21 V
1762233598	12 Pkt	-28 dBm	21 V
1762232735	10 Pkt	-29 dBm	21 V
1762231871	10 Pkt	-27 dBm	21 V
1762231008	11 Pkt	-28 dBm	21 V
1762230146	12 Pkt	-26 dBm	21 V
1762230145	12 Pkt	-27 dBm	21 V
1762229280	8 Pkt	-27 dBm	21 V
1762228416	9 Pkt	-27 dBm	21 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)