APRS Track Direct

My position About ☰

reset

MB7UHG Telemetry

This is the latest recevied telemetry packets stored in our database for station/object MB7UHG. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	CabT*
1774136644	13.8 Volt	100 Pcnt	158 c
1774135744	13.8 Volt	100 Pcnt	158 c
1774134844	13.8 Volt	100 Pcnt	158 c
1774133944	13.8 Volt	100 Pcnt	158 c
1774133044	13.8 Volt	100 Pcnt	158 c
1774132144	13.88 Volt	100 Pcnt	159 c
1774131244	13.8 Volt	100 Pcnt	160 c
1774130344	13.8 Volt	100 Pcnt	160 c
1774129444	13.88 Volt	100 Pcnt	161 c
1774128544	13.8 Volt	100 Pcnt	162 c
1774127644	13.8 Volt	100 Pcnt	163 c
1774126744	13.8 Volt	100 Pcnt	163 c
1774125845	13.8 Volt	100 Pcnt	164 c
1774124945	13.8 Volt	100 Pcnt	165 c
1774124044	13.8 Volt	100 Pcnt	166 c
1774123144	13.8 Volt	100 Pcnt	166 c
1774122245	13.8 Volt	100 Pcnt	167 c
1774121345	13.8 Volt	100 Pcnt	168 c
1774120445	13.8 Volt	100 Pcnt	169 c
1774119545	13.8 Volt	100 Pcnt	170 c
1774118645	13.8 Volt	100 Pcnt	171 c
1774117745	13.8 Volt	100 Pcnt	172 c
1774116845	13.8 Volt	100 Pcnt	173 c
1774115945	13.8 Volt	100 Pcnt	175 c
1774115045	13.8 Volt	50 Pcnt	176 c

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

CabT: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)