APRS Track Direct

My position About ☰

reset

F6ZDV-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F6ZDV-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxPkts*	RxPkts*	Vbat*
1786731945	5 Count	2 Count	3.73 V
1786731034	5 Count	2 Count	3.73 V
1786730125	5 Count	2 Count	3.72 V
1786729216	5 Count	2 Count	3.71 V
1786728306	5 Count	2 Count	3.73 V
1786727397	5 Count	2 Count	3.82 V
1786726488	4 Count	1 Count	3.86 V
1786725578	5 Count	2 Count	3.89 V
1786724668	5 Count	2 Count	3.92 V
1786722851	4 Count	1 Count	3.93 V
1786721940	5 Count	2 Count	3.94 V
1786721031	5 Count	2 Count	3.94 V
1786720122	5 Count	2 Count	3.93 V
1786719212	5 Count	2 Count	3.93 V
1786718303	5 Count	2 Count	3.93 V
1786717395	5 Count	2 Count	3.93 V
1786716484	5 Count	2 Count	3.92 V
1786715575	5 Count	2 Count	3.91 V
1786713757	4 Count	1 Count	3.87 V
1786712847	5 Count	2 Count	3.87 V
1786710119	5 Count	2 Count	3.86 V
1786709210	4 Count	1 Count	3.85 V
1786708301	5 Count	2 Count	3.84 V
1786707391	5 Count	2 Count	3.82 V
1786706482	5 Count	2 Count	3.78 V

*Used Equation Coefficients:

TxPkts: 0, 1, 0

RxPkts: 0, 1, 0

Vbat: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)