APRS Track Direct

My position About ☰

reset

YM4KMU Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YM4KMU. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1770100248	39 Pkt	31 dBm	12.12 V
1770099319	53 Pkt	31 dBm	12.08 V
1770098390	54 Pkt	31 dBm	12.06 V
1770097460	52 Pkt	31 dBm	11.98 V
1770096529	32 Pkt	31 dBm	11.94 V
1770093745	29 Pkt	31 dBm	11.94 V
1770092817	45 Pkt	31 dBm	11.94 V
1770091888	39 Pkt	31 dBm	11.92 V
1770090960	43 Pkt	31 dBm	11.92 V
1770089102	41 Pkt	31 dBm	11.94 V
1770087244	28 Pkt	31 dBm	11.94 V
1770086316	26 Pkt	31 dBm	11.96 V
1770085389	31 Pkt	31 dBm	11.96 V
1770084460	31 Pkt	31 dBm	11.96 V
1770083533	36 Pkt	31 dBm	11.98 V
1770082605	42 Pkt	31 dBm	11.96 V
1770080749	27 Pkt	31 dBm	11.94 V
1770079822	25 Pkt	31 dBm	11.96 V
1770078894	35 Pkt	31 dBm	11.96 V
1770077965	51 Pkt	31 dBm	11.96 V
1770077036	45 Pkt	31 dBm	11.96 V
1770076107	35 Pkt	31 dBm	11.96 V
1770075179	55 Pkt	31 dBm	11.98 V
1770074251	38 Pkt	31 dBm	11.98 V
1770073323	52 Pkt	31 dBm	11.98 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)