APRS Track Direct

My position About ☰

reset

EA2RCJ-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object EA2RCJ-15. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Eff*	Volt*	Temp*
1766278646	2 Pcnt	12.43 Volt	-64 C
1766276846	2 Pcnt	12.43 Volt	-64 C
1766275046	2 Pcnt	12.43 Volt	-64 C
1766273247	2 Pcnt	12.43 Volt	-64 C
1766271447	2 Pcnt	12.43 Volt	-64 C
1766269647	2 Pcnt	12.43 Volt	-64 C
1766267847	2 Pcnt	12.43 Volt	-64 C
1766266047	2 Pcnt	12.43 Volt	-64 C
1766264247	2 Pcnt	12.43 Volt	-64 C
1766262447	2 Pcnt	12.43 Volt	-64 C
1766260647	2 Pcnt	12.43 Volt	-64 C
1766258847	2 Pcnt	12.43 Volt	-64 C
1766257047	2 Pcnt	12.43 Volt	-64 C
1766255247	2 Pcnt	12.43 Volt	-64 C
1766253447	2 Pcnt	12.43 Volt	-64 C
1766251647	2 Pcnt	12.43 Volt	-64 C
1766249847	2 Pcnt	12.43 Volt	-64 C
1766248047	2 Pcnt	12.43 Volt	-64 C
1766246248	2 Pcnt	12.43 Volt	-64 C
1766244448	2 Pcnt	12.43 Volt	-64 C
1766242648	2 Pcnt	12.43 Volt	-64 C
1766240848	2 Pcnt	12.43 Volt	-64 C
1766239048	2 Pcnt	12.43 Volt	-64 C
1766237248	2 Pcnt	12.43 Volt	-64 C
1766235448	2 Pcnt	12.43 Volt	-64 C

*Used Equation Coefficients:

Rx1h: 0, 10, 0

Eff: 0, 1, 0

Volt: 0, 0.074, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)