APRS Track Direct

My position About ☰

reset

9W2CJD-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 9W2CJD-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1762218018	0 Pkt	-36 dBm	0.06 V
1762217094	1 Pkt	-35 dBm	0.08 V
1762216170	1 Pkt	-36 dBm	0.08 V
1762215246	0 Pkt	-34 dBm	0.08 V
1762214323	1 Pkt	-37 dBm	0.06 V
1762213399	0 Pkt	-38 dBm	0.08 V
1762212476	0 Pkt	-38 dBm	0.06 V
1762211553	1 Pkt	-39 dBm	0.06 V
1762210629	0 Pkt	-39 dBm	0.08 V
1762209706	1 Pkt	-38 dBm	0.08 V
1762208781	0 Pkt	-39 dBm	0.06 V
1762207858	0 Pkt	-39 dBm	0.08 V
1762206935	0 Pkt	-38 dBm	0.08 V
1762206012	0 Pkt	-38 dBm	0.08 V
1762205089	1 Pkt	-38 dBm	0.06 V
1762204166	2 Pkt	-38 dBm	0.08 V
1762203241	0 Pkt	-38 dBm	0.08 V
1762202318	0 Pkt	-37 dBm	0.06 V
1762201396	1 Pkt	-39 dBm	0.08 V
1762200471	2 Pkt	-39 dBm	0.06 V
1762199546	2 Pkt	-40 dBm	0.06 V
1762198621	0 Pkt	-39 dBm	0.08 V
1762197698	0 Pkt	-39 dBm	0.08 V
1762196775	0 Pkt	-38 dBm	0.08 V
1762194490	0 Pkt	-38 dBm	0.08 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)