APRS Track Direct

My position About ☰

reset

YM9KE Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YM9KE. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	RxTraffic*	RSSI*	Voltage*
1770136258	1 Pkt	-48 dBm	0.88 V
1770135934	1 Pkt	-49 dBm	0.66 V
1770135611	3 Pkt	-47 dBm	0.64 V
1770135288	5 Pkt	-47 dBm	0.66 V
1770134963	10 Pkt	-47 dBm	0.66 V
1770134639	1 Pkt	-48 dBm	0.66 V
1770134316	1 Pkt	-48 dBm	0.74 V
1770133994	2 Pkt	-48 dBm	0.66 V
1770133670	2 Pkt	-48 dBm	0.64 V
1770133348	1 Pkt	-48 dBm	0.64 V
1770133025	2 Pkt	-48 dBm	0.64 V
1770132702	1 Pkt	-48 dBm	0.66 V
1770132380	1 Pkt	-48 dBm	0.62 V
1770132057	3 Pkt	-48 dBm	0.66 V
1770131735	1 Pkt	-48 dBm	0.64 V
1770131412	2 Pkt	-46 dBm	0.66 V
1770131088	2 Pkt	-46 dBm	0.66 V
1770130765	2 Pkt	-47 dBm	0.64 V
1770130442	2 Pkt	-48 dBm	1.07 V
1770130118	2 Pkt	-48 dBm	0.66 V
1770129795	1 Pkt	-48 dBm	0.64 V
1770129472	3 Pkt	-48 dBm	0.66 V
1770129150	1 Pkt	-45 dBm	0.62 V
1770128827	1 Pkt	-45 dBm	0.68 V
1770128505	4 Pkt	-45 dBm	0.64 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)