This is the latest recevied telemetry packets stored in our database for station/object PP5BAU-15. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time | Value1* | Value2* | Value3* | Value4* | Value5* |
---|---|---|---|---|---|
1719390332 | 16 | 1 | 249 | 11 | 112 |
1719389434 | 16 | 1 | 249 | 12 | 115 |
1719388539 | 16 | 1 | 249 | 15 | 120 |
1719387640 | 16 | 1 | 249 | 17 | 119 |
1719386744 | 16 | 1 | 249 | 17 | 119 |
1719385847 | 15 | 1 | 249 | 21 | 119 |
1719384947 | 15 | 1 | 249 | 21 | 111 |
1719384046 | 15 | 1 | 249 | 22 | 119 |
1719383147 | 15 | 1 | 248 | 20 | 120 |
1719381352 | 15 | 1 | 248 | 26 | 119 |
1719380453 | 15 | 1 | 248 | 17 | 118 |
1719379556 | 15 | 1 | 248 | 18 | 120 |
1719378659 | 15 | 1 | 248 | 15 | 113 |
1719377761 | 15 | 1 | 248 | 11 | 119 |
1719375967 | 15 | 1 | 248 | 5 | 121 |
1719375073 | 14 | 1 | 248 | 6 | 120 |
1719374176 | 14 | 1 | 248 | 9 | 121 |
1719373280 | 14 | 1 | 248 | 8 | 120 |
1719372385 | 14 | 1 | 248 | 10 | 120 |
1719371489 | 14 | 1 | 248 | 9 | 121 |
1719369697 | 14 | 1 | 248 | 13 | 115 |
1719368798 | 14 | 1 | 248 | 34 | 115 |
1719367893 | 14 | 1 | 248 | 15 | 121 |
1719366997 | 14 | 1 | 248 | 16 | 121 |
1719366101 | 14 | 1 | 248 | 17 | 119 |
*Used Equation Coefficients:
Value1: 0, 1, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)