APRS Track Direct

My position About ☰

reset

OE3XWJ-93 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE3XWJ-93. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*
1773615350	185.3 cm	6.9 °C	14 V	18 dB
1773614832	185.2 cm	6.9 °C	14 V	18 dB
1773614450	185.2 cm	6.9 °C	14 V	18 dB
1773614263	185.2 cm	6.9 °C	14 V	18 dB
1773613864	185.2 cm	6.9 °C	14 V	18 dB
1773613548	185.3 cm	6.9 °C	14 V	18 dB
1773613262	185.1 cm	6.9 °C	14 V	18 dB
1773612948	185 cm	6.9 °C	14 V	18 dB
1773612644	185.1 cm	6.9 °C	14 V	18 dB
1773612055	185.1 cm	6.9 °C	14 V	18 dB
1773610874	185.1 cm	6.9 °C	14 V	18 dB
1773610286	185.2 cm	6.9 °C	14 V	18 dB
1773608816	185.2 cm	7 °C	14 V	18 dB
1773608243	185.1 cm	7 °C	14 V	18 dB
1773607863	185.2 cm	7 °C	14 V	18 dB
1773606973	185.2 cm	7 °C	14 V	18 dB
1773606359	185.2 cm	7 °C	14 V	18 dB
1773605196	184.9 cm	7 °C	14 V	18 dB
1773604853	185.2 cm	7 °C	14 V	18 dB
1773604540	185 cm	7 °C	14 V	18 dB
1773604300	184.9 cm	7 °C	14 V	18 dB
1773603660	185 cm	7 °C	14 V	18 dB
1773603376	185.1 cm	7 °C	14 V	18 dB
1773601843	185.1 cm	7 °C	14 V	18 dB
1773601555	185.1 cm	7 °C	14 V	18 dB

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)