APRS Track Direct

My position About ☰

reset

2M0SBP-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 2M0SBP-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	V Raw*	T-in*	T-out*
1836274652	12.3 Volt	13.5 Volt	24 C	19 C
1836274503	12.3 Volt	13.5 Volt	24 C	19 C
1836274352	12.3 Volt	13.5 Volt	24 C	19 C
1836274202	12.3 Volt	13.4 Volt	24 C	19 C
1836274052	12.3 Volt	13.4 Volt	24 C	19 C
1762372775	12.3 Volt	13.4 Volt	23.5 C	18 C
1762372774	12.3 Volt	13.4 Volt	23.5 C	18 C
1762372474	12.3 Volt	13.3 Volt	23.5 C	18 C
1762372174	12.3 Volt	13.3 Volt	23.5 C	18 C
1762371874	12.3 Volt	13.3 Volt	23.5 C	18 C
1762371574	12.38 Volt	13.3 Volt	23.5 C	18 C
1762371274	12.3 Volt	13.3 Volt	23.5 C	18 C
1762370975	12.3 Volt	13.3 Volt	23.5 C	18 C
1762370974	12.3 Volt	13.3 Volt	23.5 C	18 C
1762370674	12.3 Volt	13.3 Volt	23.5 C	18 C
1762370375	12.3 Volt	13.3 Volt	23.5 C	18 C
1762370374	12.3 Volt	13.3 Volt	23.5 C	18 C
1762370074	12.3 Volt	13.3 Volt	23.5 C	18 C
1762369775	12.3 Volt	13.3 Volt	23.5 C	18 C
1762369774	12.3 Volt	13.3 Volt	23.5 C	18 C
1762369474	12.3 Volt	13.3 Volt	23.5 C	18 C
1762369175	12.3 Volt	13.3 Volt	23.5 C	18 C
1762369174	12.3 Volt	13.3 Volt	23.5 C	18 C
1762368874	12.3 Volt	13.3 Volt	23.5 C	18 C
1762368575	12.38 Volt	13.3 Volt	23.5 C	18 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

V Raw: 0, 0.1, 0

DgR: 0, 0.001, 0

T-in: 0, 0.5, -64

T-out: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)