APRS Track Direct

My position About ☰

reset

MB7UJ Telemetry

This is the latest recevied telemetry packets stored in our database for station/object MB7UJ. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Roof*	H'sink*	Value3*	Value4*	Value5*
1786725597	46 deg C	43 deg C	84	47	123
1786723797	46 deg C	43 deg C	84	47	123
1786721997	46 deg C	43 deg C	84	47	123
1786720197	46 deg C	42 deg C	84	47	123
1786718397	46 deg C	42 deg C	84	47	123
1786716597	46 deg C	42 deg C	84	47	123
1786714797	46 deg C	42 deg C	84	47	123
1786712997	46 deg C	42 deg C	84	47	123
1786711197	46 deg C	42 deg C	84	47	123
1786709397	46 deg C	42 deg C	84	47	123
1786707597	46 deg C	42 deg C	83	47	123
1786705796	46 deg C	42 deg C	83	47	123
1786703996	46 deg C	42 deg C	84	47	123
1786702196	46 deg C	42 deg C	84	47	123
1786700396	46 deg C	42 deg C	84	47	123
1786698596	46 deg C	42 deg C	84	47	123
1786696796	46 deg C	43 deg C	84	47	123
1786694996	46 deg C	43 deg C	84	47	123
1786693196	46 deg C	43 deg C	84	47	123
1786691396	46 deg C	43 deg C	84	47	123
1786689596	46 deg C	43 deg C	84	47	123
1786687796	45 deg C	44 deg C	84	47	123
1786685996	46 deg C	44 deg C	84	47	123
1786684196	45 deg C	44 deg C	84	47	123
1786682396	45 deg C	44 deg C	84	47	123

*Used Equation Coefficients:

Roof: 0, 1, -126

H'sink: 0, 1, -126

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)