This is the latest recevied telemetry packets stored in our database for station/object OE3PDB-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Vin* | Rx1h* | Dg1h* | Eff1h* | Rx10m* |
|---|---|---|---|---|---|
| 1732291299 | 13.04 Volt | 870 Pkt | 0 Pkt | 84 Pcnt | 134 Pkt |
| 1732287699 | 13.04 Volt | 820 Pkt | 0 Pkt | 82 Pcnt | 116 Pkt |
| 1732284099 | 13.04 Volt | 900 Pkt | 0 Pkt | 84 Pcnt | 150 Pkt |
| 1732280500 | 13.04 Volt | 830 Pkt | 0 Pkt | 85 Pcnt | 144 Pkt |
| 1732276900 | 13.04 Volt | 690 Pkt | 0 Pkt | 85 Pcnt | 110 Pkt |
| 1732273300 | 13.04 Volt | 720 Pkt | 0 Pkt | 85 Pcnt | 111 Pkt |
| 1732269700 | 13.04 Volt | 610 Pkt | 0 Pkt | 85 Pcnt | 90 Pkt |
| 1732266100 | 13.04 Volt | 650 Pkt | 0 Pkt | 83 Pcnt | 91 Pkt |
| 1732262500 | 13.04 Volt | 740 Pkt | 0 Pkt | 81 Pcnt | 117 Pkt |
| 1732258900 | 13.04 Volt | 630 Pkt | 0 Pkt | 84 Pcnt | 82 Pkt |
| 1732255300 | 13.04 Volt | 700 Pkt | 0 Pkt | 83 Pcnt | 112 Pkt |
| 1732251701 | 13.04 Volt | 720 Pkt | 0 Pkt | 80 Pcnt | 114 Pkt |
| 1732248101 | 13.04 Volt | 710 Pkt | 0 Pkt | 80 Pcnt | 99 Pkt |
| 1732244501 | 13.04 Volt | 730 Pkt | 0 Pkt | 78 Pcnt | 100 Pkt |
*Used Equation Coefficients:
Vin: 0, 0.079, 0
Rx1h: 0, 10, 0
Dg1h: 0, 10, 0
Eff1h: 0, 1, 0
Rx10m: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)