APRS Track Direct

My position About ☰

reset

W8SP-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W8SP-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*	Temp*
1766265571	11.7 Volt	220 Pkt	150 Pkt	64 Pcnt	9 C
1766261971	11.7 Volt	280 Pkt	200 Pkt	69 Pcnt	9 C
1766258371	11.7 Volt	270 Pkt	180 Pkt	56 Pcnt	8 C
1766247572	11.78 Volt	920 Pkt	330 Pkt	64 Pcnt	4 C
1766243973	11.85 Volt	930 Pkt	290 Pkt	66 Pcnt	3 C
1766240372	11.78 Volt	780 Pkt	310 Pkt	63 Pcnt	2.5 C
1766236772	11.85 Volt	750 Pkt	310 Pkt	61 Pcnt	2 C
1766233172	11.85 Volt	780 Pkt	300 Pkt	64 Pcnt	2 C
1766229573	11.78 Volt	800 Pkt	270 Pkt	68 Pcnt	2 C
1766225973	11.78 Volt	830 Pkt	300 Pkt	71 Pcnt	2 C
1766218773	11.85 Volt	680 Pkt	290 Pkt	70 Pcnt	2.5 C
1766215173	11.78 Volt	500 Pkt	260 Pkt	59 Pcnt	2.5 C
1766211573	11.78 Volt	530 Pkt	240 Pkt	61 Pcnt	3 C
1766207974	11.85 Volt	480 Pkt	240 Pkt	66 Pcnt	3.5 C
1766204374	11.85 Volt	360 Pkt	200 Pkt	70 Pcnt	3.5 C
1766197174	11.85 Volt	370 Pkt	230 Pkt	85 Pcnt	3.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)