APRS Track Direct

My position About ☰

reset

YM5KST-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YM5KST-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1754147143	0 Pkt	-61 dBm	10.83 V
1754146407	0 Pkt	-62 dBm	10.83 V
1754145610	1 Pkt	-62 dBm	10.85 V
1754144881	0 Pkt	-63 dBm	10.85 V
1754142558	0 Pkt	-62 dBm	10.79 V
1754141743	0 Pkt	-61 dBm	10.79 V
1754139937	0 Pkt	-59 dBm	10.83 V
1754139134	0 Pkt	-60 dBm	10.79 V
1754138373	0 Pkt	-63 dBm	10.79 V
1754137637	0 Pkt	-61 dBm	10.77 V
1754136869	0 Pkt	-63 dBm	10.75 V
1754136028	0 Pkt	-61 dBm	10.79 V
1754135203	0 Pkt	-62 dBm	10.79 V
1754134322	1 Pkt	-62 dBm	10.77 V
1754133555	1 Pkt	-62 dBm	10.77 V
1754133185	0 Pkt	-61 dBm	10.77 V
1754132418	0 Pkt	-62 dBm	10.75 V
1754131688	0 Pkt	-61 dBm	10.77 V
1754129754	0 Pkt	-61 dBm	10.77 V
1754129647	0 Pkt	-61 dBm	10.77 V
1754128867	0 Pkt	-60 dBm	10.75 V
1754128099	0 Pkt	-60 dBm	10.75 V
1754127369	0 Pkt	-61 dBm	10.77 V
1754124849	0 Pkt	-61 dBm	10.75 V
1754124096	0 Pkt	-62 dBm	10.75 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)