APRS Track Direct

My position About ☰

reset

TA7GUL-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA7GUL-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	RxTraffic*	RSSI*	Voltage*
1836274554	14 Pkt	-71 dBm	0.06 V
1762287736	0 Pkt	-66 dBm	0.06 V
1762284924	0 Pkt	-67 dBm	0.06 V
1762281445	0 Pkt	-66 dBm	0.06 V
1762277712	0 Pkt	-67 dBm	0.06 V
1762274591	0 Pkt	-67 dBm	0.06 V
1762272963	0 Pkt	-67 dBm	0.06 V
1762272334	0 Pkt	-66 dBm	0.06 V
1762268709	0 Pkt	-69 dBm	0.06 V
1762265432	0 Pkt	-69 dBm	0.06 V
1762261476	0 Pkt	-68 dBm	0.06 V
1762257932	0 Pkt	-67 dBm	0.06 V
1762251980	0 Pkt	-67 dBm	0.06 V
1762248346	0 Pkt	-66 dBm	0.06 V
1762247293	0 Pkt	-66 dBm	0.06 V
1762245981	0 Pkt	-67 dBm	0.06 V
1762242312	0 Pkt	-66 dBm	0.06 V
1762238652	0 Pkt	-67 dBm	0.06 V
1762235091	2 Pkt	-66 dBm	0.06 V
1762231407	0 Pkt	-67 dBm	0.06 V
1762227785	0 Pkt	-67 dBm	0.06 V
1762224163	0 Pkt	-71 dBm	0.06 V
1762220541	0 Pkt	-72 dBm	0.06 V
1762216919	0 Pkt	-71 dBm	0.06 V
1762213297	0 Pkt	-67 dBm	0.06 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)