APRS Track Direct

My position About ☰

reset

VE7SML-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VE7SML-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Voltage*	Solar *	temp*
1758224283	15.1 volts	0.02 amps	18.5 deg C
1758223985	14.73 volts	0.02 amps	18.5 deg C
1758223983	14.73 volts	0.02 amps	18.5 deg C
1758223683	14.8 volts	0.02 amps	18.5 deg C
1758223385	14.73 volts	0.02 amps	18.5 deg C
1758223383	14.73 volts	0.02 amps	18.5 deg C
1758223083	15.03 volts	0.02 amps	19 deg C
1758222783	14.65 volts	0.02 amps	19 deg C
1758222483	14.73 volts	0.02 amps	19 deg C
1758222183	14.73 volts	0.02 amps	0 deg C
1758221883	14.73 volts	0.02 amps	0 deg C
1758221583	14.73 volts	0.02 amps	0 deg C
1758221283	14.73 volts	0.02 amps	0 deg C
1758220983	14.73 volts	0.02 amps	0 deg C
1758220683	14.73 volts	0.02 amps	0 deg C
1758220383	14.73 volts	0.02 amps	0 deg C
1758220083	15.03 volts	0.02 amps	0 deg C
1758219783	14.8 volts	0.02 amps	0 deg C
1758219483	14.8 volts	0.02 amps	0 deg C
1758219183	14.8 volts	0.02 amps	0 deg C
1758218883	14.73 volts	0.02 amps	0 deg C
1758218583	14.88 volts	0.02 amps	0 deg C
1758218283	14.8 volts	0.02 amps	0 deg C
1758217983	14.8 volts	0.02 amps	0 deg C
1758217683	14.8 volts	0.02 amps	0 deg C

*Used Equation Coefficients:

Voltage: 0, 0.075, 3.55

Solar : 0, 0.195, -24.94

temp: 0, 0.5, -64

Value4: 0, 0, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)