APRS Track Direct

My position About ☰

reset

HS6YHE-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS6YHE-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RxTraffic*	TxTraffic*	RSSI*	Voltage*
1758165987	0 Pkt	0 Pkt	-47 dBm	0.92 V
1758164161	0 Pkt	0 Pkt	-42 dBm	0.92 V
1758162336	0 Pkt	0 Pkt	-45 dBm	0.78 V
1758160511	0 Pkt	0 Pkt	-42 dBm	1.03 V
1758158686	0 Pkt	0 Pkt	-39 dBm	1.05 V
1758156861	0 Pkt	0 Pkt	-39 dBm	1.07 V
1758155036	0 Pkt	2 Pkt	-40 dBm	1.15 V
1758153210	0 Pkt	0 Pkt	-38 dBm	1.15 V
1758151384	0 Pkt	0 Pkt	-39 dBm	1.17 V
1758149559	8 Pkt	0 Pkt	-38 dBm	1.15 V
1758147732	4 Pkt	0 Pkt	-40 dBm	1.15 V
1758145906	0 Pkt	0 Pkt	-41 dBm	1.19 V
1758144084	0 Pkt	0 Pkt	-38 dBm	0.98 V
1758142255	0 Pkt	4 Pkt	-38 dBm	1.17 V
1758140429	0 Pkt	1 Pkt	-37 dBm	1.15 V
1758138604	0 Pkt	0 Pkt	-41 dBm	1.17 V
1758136778	11 Pkt	8 Pkt	-38 dBm	1.15 V
1758134950	0 Pkt	9 Pkt	-39 dBm	1.17 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)