APRS Track Direct

My position About ☰

reset

SP8EBC-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP8EBC-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Tx10min*	Vbatt*	Tempre*
1836274411	6 Pkt	12.58 V	16.5 DegC
1836274263	6 Pkt	12.58 V	16.5 DegC
1782472134	6 Pkt	13.98 V	36 DegC
1782471530	6 Pkt	13.98 V	36 DegC
1782470931	6 Pkt	13.98 V	36 DegC
1782470327	6 Pkt	14 V	35.5 DegC
1782469728	6 Pkt	13.98 V	35.5 DegC
1782469124	6 Pkt	14 V	35.5 DegC
1782468525	6 Pkt	14 V	35 DegC
1782467920	6 Pkt	13.98 V	35.5 DegC
1782467321	7 Pkt	14 V	35 DegC
1782466718	6 Pkt	14.02 V	34.5 DegC
1782466119	6 Pkt	13.98 V	33.5 DegC
1782465515	11 Pkt	14 V	34.5 DegC
1782464917	6 Pkt	13.98 V	34 DegC
1782464299	6 Pkt	14 V	34 DegC
1782463700	6 Pkt	13.98 V	33.5 DegC
1782463097	6 Pkt	14 V	33.5 DegC
1782462498	6 Pkt	13.98 V	34 DegC
1782461893	6 Pkt	13.98 V	34.5 DegC
1782461294	6 Pkt	14 V	34 DegC
1782460690	6 Pkt	14 V	34 DegC
1782460091	6 Pkt	14 V	34 DegC
1782459487	7 Pkt	13.98 V	33.5 DegC
1782458885	6 Pkt	14 V	33.5 DegC

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)