APRS Track Direct

My position About ☰

reset

MB7UGB-0 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object MB7UGB-0. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	Temp*
1786743153	7 Pkts	6 Pkts	22 C
1786739553	8 Pkts	7 Pkts	22 C
1786735953	8 Pkts	7 Pkts	22 C
1786732353	6 Pkts	6 Pkts	23 C
1786728753	6 Pkts	5 Pkts	22 C
1786725153	120 Pkts	109 Pkts	23 C
1786721553	135 Pkts	121 Pkts	23 C
1786717953	153 Pkts	139 Pkts	23 C
1786714353	169 Pkts	153 Pkts	22 C
1786710753	135 Pkts	121 Pkts	22 C
1786707153	133 Pkts	118 Pkts	22 C
1786703553	156 Pkts	138 Pkts	22 C
1786699954	177 Pkts	162 Pkts	21 C
1786696354	189 Pkts	176 Pkts	22 C
1786692754	178 Pkts	164 Pkts	22 C
1786689153	249 Pkts	236 Pkts	21 C
1786685553	255 Pkts	242 Pkts	22 C
1786681953	178 Pkts	164 Pkts	22 C
1786678353	173 Pkts	159 Pkts	22 C
1786674753	142 Pkts	129 Pkts	22 C
1786671153	168 Pkts	155 Pkts	22 C
1786667553	192 Pkts	181 Pkts	22 C
1786663953	251 Pkts	239 Pkts	22 C
1786660353	274 Pkts	262 Pkts	22 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

Temp: 0, 1, 0

V1: 0, 0.1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)