APRS Track Direct

My position About ☰

reset

LU2DGE-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU2DGE-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	CPU*	MB*	RAM*	FAN*	VCORE*
1782516602	33 °C	25 °C	24 %	1290 RPM	1.1 V
1782514802	32 °C	25 °C	24 %	1305 RPM	1.1 V
1782513003	32 °C	25 °C	24 %	1305 RPM	1.1 V
1782511203	33 °C	25 °C	24 %	1305 RPM	1.1 V
1782509402	32 °C	25 °C	24 %	1290 RPM	1.1 V
1782507603	32 °C	25 °C	24 %	1290 RPM	1.1 V
1782505802	32 °C	25 °C	23 %	1305 RPM	1.1 V
1782504003	32 °C	25 °C	23 %	1290 RPM	1.1 V
1782502202	32 °C	25 °C	23 %	1290 RPM	1.1 V
1782500403	31 °C	25 °C	23 %	1290 RPM	1.1 V
1782498602	31 °C	25 °C	23 %	1290 RPM	1.1 V
1782496802	31 °C	25 °C	23 %	1290 RPM	1.1 V
1782495003	31 °C	25 °C	23 %	1305 RPM	1.1 V
1782493202	31 °C	24 °C	22 %	1290 RPM	1.1 V
1782491402	31 °C	24 °C	22 %	1290 RPM	1.1 V
1782489602	31 °C	24 °C	23 %	1290 RPM	1.1 V
1782487803	31 °C	24 °C	23 %	1290 RPM	1.1 V
1782486002	30 °C	24 °C	23 %	1290 RPM	1.1 V
1782484203	30 °C	24 °C	23 %	1290 RPM	1.1 V
1782482402	30 °C	24 °C	22 %	1290 RPM	1.1 V
1782480603	30 °C	24 °C	23 %	1290 RPM	1.1 V
1782478802	30 °C	23 °C	22 %	1290 RPM	1.1 V
1782441003	33 °C	27 °C	23 %	1290 RPM	1.1 V
1782439204	34 °C	27 °C	24 %	1305 RPM	1.25 V
1782437403	33 °C	27 °C	24 %	1305 RPM	1.25 V

*Used Equation Coefficients:

CPU: 0, 1, 0

MB: 0, 1, 0

RAM: 0, 1, 0

FAN: 0, 15, 0

VCORE: 0, 0.01, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)