APRS Track Direct

My position About ☰

reset

KC0CAP-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KC0CAP-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx1h*	Dg1h*	Eff1h*
1786727209	1080 Pkt	100 Pkt	70 Pcnt
1786727208	1080 Pkt	100 Pkt	70 Pcnt
1786726908	1100 Pkt	90 Pkt	71 Pcnt
1786726611	1120 Pkt	90 Pkt	71 Pcnt
1786726608	1120 Pkt	90 Pkt	71 Pcnt
1786722674	1110 Pkt	70 Pkt	69 Pcnt
1786722375	1120 Pkt	70 Pkt	70 Pcnt
1786722374	1120 Pkt	70 Pkt	70 Pcnt
1786722074	1120 Pkt	70 Pkt	69 Pcnt
1786721775	1130 Pkt	70 Pkt	70 Pcnt
1786721774	1130 Pkt	70 Pkt	70 Pcnt
1786721474	1140 Pkt	70 Pkt	69 Pcnt
1786721175	1150 Pkt	70 Pkt	69 Pcnt
1786721174	1150 Pkt	70 Pkt	69 Pcnt
1786720874	1170 Pkt	70 Pkt	69 Pcnt
1786720576	1170 Pkt	70 Pkt	69 Pcnt
1786720574	1170 Pkt	70 Pkt	69 Pcnt
1786720274	1210 Pkt	70 Pkt	70 Pcnt
1786719975	1250 Pkt	70 Pkt	70 Pcnt
1786719974	1250 Pkt	70 Pkt	70 Pcnt
1786719674	1260 Pkt	70 Pkt	70 Pcnt
1786719375	1280 Pkt	70 Pkt	70 Pcnt
1786719374	1280 Pkt	70 Pkt	70 Pcnt
1786719074	1300 Pkt	70 Pkt	70 Pcnt
1786718775	1330 Pkt	70 Pkt	71 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)