APRS Track Direct

My position About ☰

reset

ED1ZAW-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED1ZAW-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Volt.*	Rx/h*	Digi/h*	Efic*
1732306579	13.95 V.	260 Pkt	80 Pkt	87 %
1732306340	13.88 V.	270 Pkt	80 Pkt	87 %
1732305860	13.95 V.	300 Pkt	90 Pkt	87 %
1732305740	13.95 V.	300 Pkt	90 Pkt	87 %
1732305140	13.95 V.	300 Pkt	100 Pkt	87 %
1732305139	13.95 V.	300 Pkt	100 Pkt	87 %
1732304540	13.95 V.	330 Pkt	120 Pkt	87 %
1732304419	13.88 V.	330 Pkt	120 Pkt	87 %
1732303940	13.95 V.	360 Pkt	130 Pkt	87 %
1732303699	13.95 V.	370 Pkt	130 Pkt	87 %
1732303340	13.95 V.	380 Pkt	130 Pkt	87 %
1732302979	13.95 V.	400 Pkt	140 Pkt	87 %
1732302740	13.95 V.	390 Pkt	140 Pkt	87 %
1732302260	13.88 V.	390 Pkt	150 Pkt	87 %
1732302142	13.88 V.	380 Pkt	150 Pkt	87 %
1732301540	13.8 V.	370 Pkt	150 Pkt	87 %
1732301540	13.8 V.	370 Pkt	150 Pkt	87 %
1732300940	13.95 V.	350 Pkt	140 Pkt	87 %
1732300819	13.95 V.	340 Pkt	140 Pkt	87 %
1732300100	13.95 V.	340 Pkt	130 Pkt	87 %
1732299740	13.88 V.	330 Pkt	120 Pkt	87 %
1732299380	13.95 V.	320 Pkt	110 Pkt	87 %
1732299140	13.95 V.	300 Pkt	110 Pkt	87 %
1732298660	13.8 V.	300 Pkt	90 Pkt	87 %
1732298540	13.95 V.	290 Pkt	90 Pkt	87 %

*Used Equation Coefficients:

Volt.: 0, 0.075, 0

Rx/h: 0, 10, 0

Digi/h: 0, 10, 0

Temp: 0, 0.5, -64

Efic: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)