APRS Track Direct

My position About ☰

reset

E22UYE-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E22UYE-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1758277253	0 Pkt	-66 dBm	14.05 V
1758276328	0 Pkt	-71 dBm	13.97 V
1758275404	0 Pkt	-72 dBm	14.03 V
1758274480	0 Pkt	-66 dBm	14.05 V
1758273556	1 Pkt	-63 dBm	14.05 V
1758272632	3 Pkt	-68 dBm	14.05 V
1758271708	0 Pkt	-68 dBm	14.07 V
1758270784	0 Pkt	-69 dBm	14.05 V
1758269859	0 Pkt	-61 dBm	14.07 V
1758268935	0 Pkt	-67 dBm	14.07 V
1758268011	1 Pkt	-62 dBm	14.07 V
1758267086	1 Pkt	-68 dBm	14.09 V
1758266162	0 Pkt	-61 dBm	14.07 V
1758265238	0 Pkt	-62 dBm	14.09 V
1758264314	0 Pkt	-62 dBm	14.09 V
1758263389	0 Pkt	-62 dBm	14.09 V
1758262465	0 Pkt	-62 dBm	14.03 V
1758261541	0 Pkt	-67 dBm	14.11 V
1758260617	0 Pkt	-67 dBm	14.11 V
1758259693	2 Pkt	-62 dBm	14.11 V
1758258770	1 Pkt	-62 dBm	14.13 V
1758257844	0 Pkt	-62 dBm	14.11 V
1758256920	0 Pkt	-62 dBm	14.13 V
1758255996	0 Pkt	-63 dBm	14.13 V
1758255071	1 Pkt	-62 dBm	14.15 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)