APRS Track Direct

My position About ☰

reset

SQ7BCZ-14 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ7BCZ-14. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Rx1h*	Dg1h*	Temp*
1754135629	12.68 Volt	4 Pkt	1 Pkt	23 C
1754133829	12.68 Volt	4 Pkt	1 Pkt	22.5 C
1754132029	12.68 Volt	3 Pkt	1 Pkt	22 C
1754130229	12.68 Volt	4 Pkt	2 Pkt	22 C
1754128429	12.68 Volt	3 Pkt	1 Pkt	22 C
1754126629	12.68 Volt	1 Pkt	0 Pkt	21 C
1754124829	12.68 Volt	1 Pkt	0 Pkt	20.5 C
1754123029	12.68 Volt	1 Pkt	0 Pkt	20 C
1754121229	12.68 Volt	2 Pkt	0 Pkt	20 C
1754119429	12.68 Volt	2 Pkt	0 Pkt	19.5 C
1754117629	12.68 Volt	2 Pkt	0 Pkt	20 C
1754115829	12.68 Volt	2 Pkt	0 Pkt	20 C
1754114029	12.68 Volt	2 Pkt	0 Pkt	19.5 C
1754112229	12.68 Volt	2 Pkt	0 Pkt	19.5 C
1754110429	12.68 Volt	2 Pkt	0 Pkt	19.5 C
1754108629	12.68 Volt	2 Pkt	0 Pkt	19 C
1754106830	12.68 Volt	2 Pkt	0 Pkt	19 C
1754105030	12.68 Volt	2 Pkt	0 Pkt	18.5 C
1754103230	12.68 Volt	2 Pkt	0 Pkt	19 C
1754101430	12.68 Volt	2 Pkt	0 Pkt	19 C
1754099630	12.68 Volt	2 Pkt	0 Pkt	19 C
1754097830	12.68 Volt	2 Pkt	0 Pkt	19.5 C
1754096030	12.68 Volt	2 Pkt	0 Pkt	19.5 C
1754094230	12.68 Volt	2 Pkt	0 Pkt	21 C
1754092430	12.75 Volt	2 Pkt	0 Pkt	21 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 1, 0

Dg1h: 0, 1, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)