APRS Track Direct

My position About ☰

reset

OM0OPC-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OM0OPC-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1836274602	13.95 Volt	530 Pkt	49 Pcnt
1836274452	13.95 Volt	560 Pkt	51 Pcnt
1836274003	13.95 Volt	500 Pkt	48 Pcnt
1762355095	13.95 Volt	620 Pkt	56 Pcnt
1762354495	13.95 Volt	610 Pkt	56 Pcnt
1762353895	13.95 Volt	590 Pkt	57 Pcnt
1762353295	13.95 Volt	610 Pkt	59 Pcnt
1762352695	13.95 Volt	630 Pkt	62 Pcnt
1762352095	13.95 Volt	640 Pkt	64 Pcnt
1762351495	13.95 Volt	690 Pkt	67 Pcnt
1762350895	13.95 Volt	680 Pkt	67 Pcnt
1762350295	13.95 Volt	730 Pkt	69 Pcnt
1762349695	13.95 Volt	730 Pkt	71 Pcnt
1762349095	13.95 Volt	740 Pkt	74 Pcnt
1762348497	13.95 Volt	760 Pkt	75 Pcnt
1762348495	13.95 Volt	760 Pkt	75 Pcnt
1762347895	13.95 Volt	720 Pkt	72 Pcnt
1762347295	13.95 Volt	650 Pkt	71 Pcnt
1762346695	13.95 Volt	580 Pkt	68 Pcnt
1762346095	13.95 Volt	520 Pkt	65 Pcnt
1762345495	13.95 Volt	420 Pkt	59 Pcnt
1762344897	13.95 Volt	360 Pkt	56 Pcnt
1762344895	13.95 Volt	360 Pkt	56 Pcnt
1762344295	13.95 Volt	350 Pkt	57 Pcnt
1762343695	13.95 Volt	350 Pkt	57 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

DgS: 0, 0.001, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)