This is the latest recevied telemetry packets stored in our database for station/object WALDEN. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time | Value1* | Value2* | Value3* | Value4* | Value5* |
---|---|---|---|---|---|
1753518317 | 125 | 52 | 70 | 41 | 48 |
1753517717 | 126 | 54 | 72 | 40 | 48 |
1753516526 | 126 | 53 | 71 | 41 | 48 |
1753515327 | 111 | 40 | 49 | 64 | 48 |
1753514733 | 126 | 52 | 71 | 41 | 48 |
1753514135 | 126 | 52 | 70 | 41 | 48 |
1753513540 | 126 | 52 | 72 | 41 | 48 |
1753512942 | 126 | 52 | 71 | 41 | 48 |
1753511741 | 126 | 52 | 66 | 41 | 48 |
1753511145 | 126 | 55 | 70 | 41 | 48 |
1753510550 | 126 | 65 | 70 | 41 | 48 |
1753509356 | 126 | 57 | 70 | 41 | 63 |
1753507568 | 126 | 52 | 71 | 41 | 48 |
1753506970 | 123 | 45 | 62 | 41 | 48 |
1753506369 | 126 | 52 | 69 | 41 | 48 |
1753505777 | 126 | 63 | 87 | 41 | 48 |
1753505179 | 126 | 66 | 68 | 41 | 48 |
1753504580 | 113 | 44 | 59 | 42 | 48 |
1753503982 | 127 | 50 | 71 | 41 | 48 |
1753503387 | 126 | 53 | 70 | 41 | 48 |
1753502789 | 127 | 52 | 68 | 41 | 48 |
1753500405 | 126 | 51 | 68 | 41 | 48 |
1753499206 | 126 | 51 | 66 | 41 | 48 |
1753498612 | 126 | 53 | 66 | 41 | 48 |
1753498013 | 127 | 52 | 66 | 41 | 48 |
*Used Equation Coefficients:
Value1: 0, 1, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)