APRS Track Direct

My position About ☰

reset

SR9NCI Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9NCI. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*
1786722599	46 Pkt	4 Pkt	0 Pkt
1786721994	39 Pkt	2 Pkt	0 Pkt
1786721391	45 Pkt	4 Pkt	0 Pkt
1786720786	42 Pkt	6 Pkt	0 Pkt
1786720176	25 Pkt	4 Pkt	0 Pkt
1786719571	36 Pkt	3 Pkt	0 Pkt
1786718967	33 Pkt	3 Pkt	0 Pkt
1786718363	37 Pkt	7 Pkt	0 Pkt
1786717753	33 Pkt	3 Pkt	0 Pkt
1786717149	38 Pkt	3 Pkt	0 Pkt
1786716545	35 Pkt	3 Pkt	0 Pkt
1786715941	49 Pkt	7 Pkt	0 Pkt
1786715330	34 Pkt	4 Pkt	0 Pkt
1786714725	37 Pkt	2 Pkt	0 Pkt
1786713517	38 Pkt	6 Pkt	0 Pkt
1786712907	23 Pkt	4 Pkt	0 Pkt
1786712302	35 Pkt	3 Pkt	0 Pkt
1786711698	27 Pkt	3 Pkt	0 Pkt
1786711095	36 Pkt	7 Pkt	0 Pkt
1786710484	36 Pkt	3 Pkt	0 Pkt
1786709880	40 Pkt	3 Pkt	0 Pkt
1786709276	39 Pkt	6 Pkt	2 Pkt
1786708671	35 Pkt	6 Pkt	0 Pkt
1786708061	38 Pkt	5 Pkt	1 Pkt
1786707456	29 Pkt	2 Pkt	0 Pkt

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

HostTx10m: 0, 1, 0

Tempre: 0, 0.25, -25

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)