APRS Track Direct

My position About ☰

reset

DC4HF-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DC4HF-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*	Value5*
1786732525	1178	5693	7481	5309	1575
1786731623	1178	5692	7482	5392	1536
1786730722	1178	5696	7488	5446	1520
1786729820	1178	5697	7488	5535	1483
1786728919	1178	5698	7490	5599	1462
1786728018	1178	5698	7490	5704	1397
1786727117	1178	5701	7492	5790	1349
1786726216	1178	5706	7495	5920	1267
1786725315	1178	5706	7496	6029	1202
1786724415	1178	5707	7502	6200	1098
1786723513	1178	5712	7508	6198	1159
1786722612	1178	5711	7507	6236	1146
1786721711	1178	5714	7512	6265	1136
1786720810	1178	5715	7510	6293	1113
1786719909	1178	5716	7501	6317	1099
1786719008	1178	5715	7506	6328	1092
1786718107	1177	5716	7505	6338	1077
1786717206	1177	5718	7507	6345	1072
1786716305	1177	5716	7503	6347	1062
1786715404	1177	5710	7501	6341	1069
1786714503	1177	5714	7500	6326	1073
1786713602	1177	5717	7507	6308	1066
1786712701	1177	5715	7506	6283	1072
1786711800	1177	5710	7503	6258	1068
1786710899	1177	5720	7510	6231	1075

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)