APRS Track Direct

My position About ☰

reset

BX6AM-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX6AM-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*	DiGi*
1836274836	42.8 C	6 p	6 p	6 p	3 p
1762350436	40.6 C	3 p	6 p	38 p	10 p
1762349236	39.7 C	3 p	6 p	38 p	10 p
1762348037	41.9 C	3 p	6 p	38 p	10 p
1762346836	41.5 C	3 p	6 p	38 p	10 p
1762345636	42.8 C	3 p	6 p	38 p	10 p
1762344438	40.6 C	2 p	5 p	35 p	9 p
1762343236	40.8 C	2 p	6 p	34 p	8 p
1762342036	41.1 C	2 p	7 p	32 p	7 p
1762340836	41.3 C	3 p	7 p	30 p	7 p
1762339636	41.4 C	3 p	5 p	28 p	6 p
1762338437	43 C	1 p	4 p	26 p	6 p
1762337236	43.1 C	2 p	3 p	25 p	5 p
1762336036	43.4 C	1 p	1 p	23 p	4 p
1762334836	44.2 C	1 p	3 p	22 p	4 p
1762333636	44.3 C	1 p	3 p	22 p	4 p
1762332436	43.6 C	1 p	3 p	22 p	4 p
1762331237	44.1 C	1 p	3 p	22 p	4 p
1762330036	43.7 C	1 p	3 p	22 p	4 p
1762328837	44 C	1 p	3 p	22 p	4 p
1762327637	43.9 C	2 p	2 p	21 p	4 p
1762326436	43.5 C	1 p	1 p	20 p	3 p
1762325237	43.7 C	1 p	3 p	19 p	2 p
1762324036	43.9 C	1 p	3 p	19 p	2 p
1762322850	44.6 C	1 p	3 p	19 p	2 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)