APRS Track Direct

My position About ☰

reset

LU1DNS-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU1DNS-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	RxTraffic*	RSSI*	Voltage*
1754151084	12 Pkt	-71 dBm	14.52 V
1754149261	30 Pkt	-71 dBm	14.27 V
1754145616	14 Pkt	-70 dBm	13.72 V
1754143793	4 Pkt	-70 dBm	13.39 V
1754141971	9 Pkt	-70 dBm	12.47 V
1754140149	13 Pkt	-71 dBm	12.47 V
1754138326	11 Pkt	-70 dBm	12.12 V
1754136503	12 Pkt	-71 dBm	12.1 V
1754134681	10 Pkt	-69 dBm	11.92 V
1754131036	6 Pkt	-70 dBm	11.89 V
1754129214	9 Pkt	-69 dBm	11.92 V
1754127392	8 Pkt	-69 dBm	11.92 V
1754125569	13 Pkt	-69 dBm	11.89 V
1754123746	9 Pkt	-69 dBm	11.94 V
1754121924	16 Pkt	-68 dBm	11.96 V
1754120100	4 Pkt	-69 dBm	11.98 V
1754118278	11 Pkt	-68 dBm	11.98 V
1754114632	15 Pkt	-70 dBm	12 V
1754112809	13 Pkt	-69 dBm	12 V
1754110987	19 Pkt	-69 dBm	12.02 V
1754109163	15 Pkt	-70 dBm	12.02 V
1754107341	24 Pkt	-69 dBm	12.02 V
1754105517	16 Pkt	-69 dBm	12.02 V
1754101870	20 Pkt	-69 dBm	12.08 V
1754098224	17 Pkt	-70 dBm	12.08 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)