APRS Track Direct

My position About ☰

reset

TA7FTH-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA7FTH-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1836274505	19 Pkt	-68 dBm	3.86 V
1836274332	20 Pkt	-70 dBm	3.86 V
1770466205	17 Pkt	-70 dBm	3.86 V
1770465281	20 Pkt	-70 dBm	3.86 V
1770464357	14 Pkt	-70 dBm	3.86 V
1770463433	66 Pkt	-70 dBm	3.83 V
1770462504	52 Pkt	-70 dBm	3.86 V
1770461577	18 Pkt	-71 dBm	3.88 V
1770460653	16 Pkt	-69 dBm	3.83 V
1770459729	17 Pkt	-70 dBm	3.83 V
1770458805	18 Pkt	-71 dBm	3.88 V
1770457882	34 Pkt	-67 dBm	3.83 V
1770456956	18 Pkt	-73 dBm	3.83 V
1770456033	46 Pkt	-72 dBm	3.83 V
1770455109	37 Pkt	-71 dBm	3.83 V
1770454184	23 Pkt	-69 dBm	3.86 V
1770453260	34 Pkt	-69 dBm	3.83 V
1770452335	27 Pkt	-68 dBm	3.83 V
1770451410	28 Pkt	-69 dBm	3.86 V
1770450484	18 Pkt	-69 dBm	3.83 V
1770449560	16 Pkt	-70 dBm	3.86 V
1770448637	16 Pkt	-71 dBm	3.86 V
1770447712	18 Pkt	-70 dBm	3.86 V
1770446788	16 Pkt	-70 dBm	3.83 V
1770445865	18 Pkt	-68 dBm	3.83 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)