APRS Track Direct

My position About ☰

reset

NA7Q-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object NA7Q-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*	Value5*
1786734069	13.56	18.6	4.46	60	67
1786733469	13.51	18.42	3.06	41	67
1786732868	13.51	17.76	3.19	43	67
1786732269	13.51	16.78	2.93	40	67
1786731669	13.56	17.29	4.73	64	67
1786731070	13.56	19.07	4.53	61	67
1786730469	13.51	19.26	3.46	47	67
1786729869	13.47	14.81	2.39	32	67
1786729270	13.47	17.9	2.73	37	67
1786728674	13.47	19.17	2.53	34	67
1786728069	13.47	17.2	1.86	25	67
1786727473	13.44	14.71	1.06	14	67
1786726870	13.42	15.23	0.46	6	67
1786726270	13.42	15.18	0.33	4	67
1786725669	13.39	15.14	0.19	3	67
1786725069	13.42	15.09	0	0	67
1786724474	13.42	15.04	0	0	67
1786723874	13.42	15	0	0	67
1786723268	13.44	14.95	0	0	67
1786722675	13.49	15.04	0	0	67
1786722068	13.42	15	0	0	67
1786721470	13.42	14.95	0	0	67
1786720871	13.44	15	0	0	67
1786720270	13.49	15.14	0	0	67
1786719669	13.39	14.95	0	0	67

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)