APRS Track Direct

My position About ☰

reset

VE3STP-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VE3STP-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	PVAVOLTAGE*	PVACURRENT*	PVAPOWER*	GENPWRTODAY*	CONPWRTODAY*
1836274730	0.17 V	0 A	0 W	0 KWH	0.03 KWH
1762334320	0.19 V	0 A	0 W	0 KWH	0.05 KWH
1762332474	0.2 V	0 A	0 W	0 KWH	0.05 KWH
1762330628	0.23 V	0 A	0 W	0 KWH	0.04 KWH
1762328782	0.25 V	0 A	0 W	0 KWH	0.04 KWH
1762326939	0.29 V	0 A	0 W	0 KWH	0.04 KWH
1762325093	0.47 V	0 A	0 W	0 KWH	0.04 KWH
1762323249	0.57 V	0 A	0 W	0 KWH	0.03 KWH
1762321405	0.66 V	0 A	0 W	0 KWH	0.03 KWH
1762319560	0.71 V	0 A	0 W	0 KWH	0.03 KWH
1762317715	0.69 V	0 A	0 W	0 KWH	0.03 KWH
1762315871	0.73 V	0 A	0 W	0 KWH	0.02 KWH
1762314026	0.72 V	0 A	0 W	0 KWH	0.02 KWH
1762312181	0.7 V	0 A	0 W	0 KWH	0.02 KWH
1762310337	0.66 V	0 A	0 W	0 KWH	0.02 KWH
1762308491	0.6 V	0 A	0 W	0 KWH	0.01 KWH
1762306648	0.45 V	0 A	0 W	0 KWH	0.01 KWH
1762304802	0.46 V	0 A	0 W	0 KWH	0 KWH
1762302959	0.23 V	0 A	0 W	0 KWH	0 KWH
1762301113	0.19 V	0 A	0 W	0 KWH	0 KWH
1762299269	0.22 V	0 A	0 W	0.34 KWH	0.16 KWH
1762297425	0.18 V	0 A	0 W	0.34 KWH	0.16 KWH
1762295579	0.63 V	0 A	0 W	0.34 KWH	0.15 KWH
1762293733	13.74 V	0 A	0 W	0.34 KWH	0.15 KWH
1762291890	13.88 V	0.08 A	1.02 W	0.34 KWH	0.15 KWH

*Used Equation Coefficients:

PVAVOLTAGE: 0, 0.01, 0

PVACURRENT: 0, 0.01, 0

PVAPOWER: 0, 0.01, 0

GENPWRTODAY: 0, 0.01, 0

CONPWRTODAY: 0, 0.01, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)