APRS Track Direct

My position About ☰

reset

E27AAA Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E27AAA. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1836274841	0 Pkt	-73 dBm	2.38 V
1836274217	0 Pkt	-75 dBm	3.71 V
1766171724	0 Pkt	-71 dBm	0.31 V
1766171100	0 Pkt	-71 dBm	0.31 V
1766170476	0 Pkt	-71 dBm	0.31 V
1766169851	0 Pkt	-71 dBm	0.33 V
1766169227	0 Pkt	-72 dBm	0.31 V
1766168603	0 Pkt	-71 dBm	0.31 V
1766167983	0 Pkt	-71 dBm	0.31 V
1766167354	0 Pkt	-72 dBm	0.45 V
1766166730	0 Pkt	-73 dBm	0.31 V
1766166113	1 Pkt	-72 dBm	0.31 V
1766165479	2 Pkt	-72 dBm	0.45 V
1766164856	0 Pkt	-71 dBm	0.45 V
1766164228	0 Pkt	-72 dBm	0.31 V
1766163605	0 Pkt	-72 dBm	0.31 V
1766162979	0 Pkt	-71 dBm	0.31 V
1766162355	2 Pkt	-71 dBm	0.31 V
1766161736	0 Pkt	-71 dBm	0.31 V
1766161351	0 Pkt	-72 dBm	0.31 V
1766160481	0 Pkt	-72 dBm	0.31 V
1766159864	0 Pkt	-71 dBm	0.45 V
1766159231	4 Pkt	-72 dBm	0.31 V
1766158681	0 Pkt	-72 dBm	0.29 V
1766157983	0 Pkt	-72 dBm	0.29 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)