APRS Track Direct

My position About ☰

reset

KK7CXF-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KK7CXF-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	OutT*	InvertT*	MainSOC*	SecSOC*	BattT*
1836274417	68 DegF	129 DegF	90 S	99 S	70
1836274267	68 DegF	129 DegF	89 S	99 S	70
1762343565	36 DegF	98 DegF	75 S	99 S	57
1762342965	36 DegF	98 DegF	75 S	99 S	57
1762342365	35 DegF	98 DegF	75 S	99 S	57
1762341765	35 DegF	98 DegF	76 S	99 S	57
1762341165	35 DegF	98 DegF	76 S	99 S	57
1762340566	36 DegF	98 DegF	77 S	99 S	57
1762339965	37 DegF	100 DegF	77 S	99 S	57
1762339365	37 DegF	100 DegF	77 S	99 S	57
1762339300	37 DegF	100 DegF	78 S	99 S	57
1762338165	37 DegF	100 DegF	78 S	99 S	57
1762337565	35 DegF	100 DegF	78 S	99 S	57
1762336966	35 DegF	100 DegF	79 S	99 S	57
1762336366	34 DegF	102 DegF	79 S	99 S	57
1762335765	34 DegF	102 DegF	79 S	99 S	57
1762335165	35 DegF	102 DegF	80 S	99 S	57
1762334565	36 DegF	102 DegF	80 S	99 S	58
1762333965	36 DegF	102 DegF	80 S	99 S	57
1762333365	36 DegF	104 DegF	81 S	99 S	57
1762332765	36 DegF	104 DegF	81 S	99 S	58
1762332166	36 DegF	104 DegF	81 S	99 S	58
1762331566	37 DegF	104 DegF	81 S	99 S	58
1762330965	37 DegF	104 DegF	82 S	99 S	58
1762330365	38 DegF	105 DegF	82 S	99 S	58

*Used Equation Coefficients:

OutT: 0, 1, 0

InvertT: 0, 1, 0

MainSOC: 0, 1, 0

SecSOC: 0, 1, 0

BattT: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)