APRS Track Direct

My position About ☰

reset

OE8KKK-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE8KKK-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	U BATCd*	TempT*	Rx 1h*	Ef 1h*
1786732999	13.6 V	30 C	290 Pkt	85 Pct
1786732998	13.6 V	30 C	290 Pkt	85 Pct
1786732698	13.6 V	30 C	300 Pkt	85 Pct
1786732397	13.6 V	30.5 C	300 Pkt	86 Pct
1786732097	13.6 V	30.5 C	290 Pkt	86 Pct
1786731797	13.6 V	30.5 C	240 Pkt	88 Pct
1786731496	13.6 V	30.5 C	250 Pkt	89 Pct
1786731197	13.6 V	30.5 C	250 Pkt	89 Pct
1786731196	13.6 V	30.5 C	250 Pkt	89 Pct
1786730896	13.6 V	31 C	250 Pkt	89 Pct
1786730596	13.6 V	31 C	240 Pkt	87 Pct
1786730295	13.6 V	31 C	240 Pkt	88 Pct
1786729995	13.6 V	31.5 C	250 Pkt	88 Pct
1786729695	13.6 V	31.5 C	240 Pkt	87 Pct
1786729395	13.6 V	31.5 C	250 Pkt	86 Pct
1786729394	13.6 V	31.5 C	250 Pkt	86 Pct
1786729094	13.6 V	31.5 C	230 Pkt	86 Pct
1786728794	13.6 V	31.5 C	230 Pkt	84 Pct
1786728493	13.6 V	31.5 C	230 Pkt	84 Pct
1786728193	13.6 V	32 C	230 Pkt	85 Pct
1786727893	13.6 V	32 C	230 Pkt	85 Pct
1786727594	13.6 V	32 C	230 Pkt	86 Pct
1786727593	13.6 V	32 C	230 Pkt	86 Pct
1786727292	13.6 V	32 C	230 Pkt	85 Pct
1786726992	13.6 V	32 C	230 Pkt	86 Pct

*Used Equation Coefficients:

I Solar: 0, 0.1687, -21.4241

U BATCd: 0, 0.1, 0

TempT: 0, 0.5, -64

Rx 1h: 0, 10, 0

Ef 1h: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)