APRS Track Direct

My position About ☰

reset

YM7KAY-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YM7KAY-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1836274271	4 Pkt	-68 dBm	12.41 V
1836274155	3 Pkt	-69 dBm	12.41 V
1770137416	0 Pkt	-67 dBm	12.41 V
1770136673	0 Pkt	-69 dBm	12.41 V
1770135930	0 Pkt	-71 dBm	12.41 V
1770135280	0 Pkt	-69 dBm	12.41 V
1770134444	0 Pkt	-72 dBm	12.41 V
1770133715	0 Pkt	-70 dBm	12.41 V
1770132988	0 Pkt	-68 dBm	12.41 V
1770132219	0 Pkt	-69 dBm	12.41 V
1770131471	0 Pkt	-67 dBm	12.41 V
1770130728	5 Pkt	-68 dBm	12.41 V
1770129984	5 Pkt	-70 dBm	12.41 V
1770129238	3 Pkt	-68 dBm	12.41 V
1770128891	0 Pkt	-68 dBm	12.41 V
1770128129	0 Pkt	-67 dBm	12.41 V
1770127385	0 Pkt	-68 dBm	12.41 V
1770126654	0 Pkt	-68 dBm	12.41 V
1770125922	0 Pkt	-67 dBm	12.41 V
1770125155	0 Pkt	-67 dBm	12.41 V
1770124415	0 Pkt	-67 dBm	12.41 V
1770123669	0 Pkt	-68 dBm	12.41 V
1770122926	0 Pkt	-68 dBm	12.41 V
1770122184	0 Pkt	-67 dBm	12.41 V
1770121440	0 Pkt	-67 dBm	12.39 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)