APRS Track Direct

My position About ☰

reset

E25RIV-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E25RIV-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1836274657	0 Pkt	-93 dBm	9.64 V
1836274531	0 Pkt	-82 dBm	9.47 V
1836274033	0 Pkt	-88 dBm	9.56 V
1782551810	0 Pkt	-76 dBm	12.39 V
1782551186	0 Pkt	-76 dBm	12.37 V
1782550562	0 Pkt	-77 dBm	12.39 V
1782549938	0 Pkt	-77 dBm	12.39 V
1782549314	0 Pkt	-76 dBm	12.37 V
1782548690	0 Pkt	-77 dBm	12.37 V
1782548065	0 Pkt	-78 dBm	12.37 V
1782547441	0 Pkt	-77 dBm	12.37 V
1782546817	0 Pkt	-76 dBm	12.37 V
1782546193	0 Pkt	-78 dBm	12.37 V
1782545569	0 Pkt	-77 dBm	12.37 V
1782544945	0 Pkt	-76 dBm	12.39 V
1782544322	0 Pkt	-79 dBm	12.39 V
1782543697	1 Pkt	-78 dBm	12.37 V
1782543073	0 Pkt	-78 dBm	12.39 V
1782542449	0 Pkt	-80 dBm	12.37 V
1782541825	0 Pkt	-77 dBm	12.37 V
1782541202	0 Pkt	-77 dBm	12.39 V
1782540578	0 Pkt	-78 dBm	12.39 V
1782539954	0 Pkt	-77 dBm	12.39 V
1782539330	0 Pkt	-77 dBm	12.39 V
1782538706	0 Pkt	-77 dBm	12.37 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)