This is the latest recevied telemetry packets stored in our database for station/object W1WRA-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Temp* | Load* | FreeMem* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1836274262 | 59.89 | 0.13 | 53 | 0 | 0 |
| 1836274113 | 59.89 | 0.18 | 50 | 0 | 0 |
| 1766223305 | 55.02 | 0.23 | 107 | 0 | 0 |
| 1766222705 | 55.02 | 0.22 | 107 | 0 | 0 |
| 1766222105 | 54.53 | 0.17 | 105 | 0 | 0 |
| 1766221505 | 55.02 | 0.24 | 110 | 0 | 0 |
| 1766220905 | 55.02 | 0.25 | 114 | 0 | 0 |
| 1766220305 | 54.53 | 0.26 | 113 | 0 | 0 |
| 1766219705 | 54.53 | 0.23 | 118 | 0 | 0 |
| 1766219105 | 54.53 | 0.15 | 123 | 0 | 0 |
| 1766218505 | 54.53 | 0.27 | 108 | 0 | 0 |
| 1766217905 | 54.53 | 0.2 | 108 | 0 | 0 |
| 1766217305 | 54.53 | 0.23 | 113 | 0 | 0 |
| 1766216705 | 54.53 | 0.19 | 111 | 0 | 0 |
| 1766216105 | 55.02 | 0.15 | 118 | 0 | 0 |
| 1766215505 | 55.02 | 0.25 | 111 | 0 | 0 |
| 1766214905 | 55.02 | 0.24 | 113 | 0 | 0 |
| 1766214305 | 54.53 | 0.2 | 112 | 0 | 0 |
| 1766213705 | 54.53 | 0.33 | 128 | 0 | 0 |
| 1766213105 | 54.53 | 0.21 | 126 | 0 | 0 |
| 1766212505 | 55.5 | 0.2 | 117 | 0 | 0 |
| 1766211905 | 55.02 | 0.27 | 123 | 0 | 0 |
| 1766211305 | 54.53 | 0.27 | 124 | 0 | 0 |
| 1766210705 | 55.5 | 0.2 | 118 | 0 | 0 |
| 1766210105 | 55.02 | 0.24 | 120 | 0 | 0 |
*Used Equation Coefficients:
Temp: 0, 0.001, 0
Load: 0, 0.001, 0
FreeMem: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)