APRS Track Direct

My position About ☰

reset

LU2DKV-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU2DKV-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1786728572	71 Pkt	-57 dBm	12.76 V
1786726748	9 Pkt	-57 dBm	12.76 V
1786724926	7 Pkt	-55 dBm	12.98 V
1786723104	69 Pkt	-54 dBm	12.74 V
1786721278	7 Pkt	-56 dBm	12.63 V
1786719456	29 Pkt	-56 dBm	12.92 V
1786717633	130 Pkt	-55 dBm	12.9 V
1786715806	42 Pkt	-61 dBm	12.74 V
1786713982	24 Pkt	-58 dBm	12.67 V
1786712837	54 Pkt	-54 dBm	13.41 V
1786711012	11 Pkt	-54 dBm	12.94 V
1786709189	3 Pkt	-55 dBm	12.8 V
1786707367	6 Pkt	-54 dBm	13.62 V
1786705544	17 Pkt	-56 dBm	13.39 V
1786703722	15 Pkt	-56 dBm	13.08 V
1786701900	8 Pkt	-56 dBm	12.98 V
1786700077	1 Pkt	-54 dBm	13.41 V
1786698255	2 Pkt	-57 dBm	13.23 V
1786696433	4 Pkt	-56 dBm	13.37 V
1786694611	10 Pkt	-55 dBm	13 V
1786692788	7 Pkt	-54 dBm	13.47 V
1786690966	0 Pkt	-57 dBm	12.88 V
1786689750	3 Pkt	-79 dBm	13.58 V
1786687872	19 Pkt	-80 dBm	13.08 V
1786686049	14 Pkt	-78 dBm	13.13 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)