APRS Track Direct

My position About ☰

reset

OE8ADF Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE8ADF. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1836274353	12.08 Volt	12 Pcnt	12 C
1836274203	12.08 Volt	0 Pcnt	12 C
1778017130	13.35 Volt	11 Pcnt	11.5 C
1778016530	13.35 Volt	11 Pcnt	11 C
1778015930	13.35 Volt	6 Pcnt	11.5 C
1778015330	13.35 Volt	7 Pcnt	11.5 C
1778014730	13.35 Volt	0 Pcnt	12 C
1778014130	13.35 Volt	0 Pcnt	12.5 C
1778013530	13.35 Volt	0 Pcnt	12.5 C
1778012930	13.35 Volt	0 Pcnt	12.5 C
1778012330	13.35 Volt	0 Pcnt	12.5 C
1778011730	13.35 Volt	0 Pcnt	12.5 C
1778011130	13.35 Volt	0 Pcnt	12.5 C
1778010530	13.35 Volt	20 Pcnt	12.5 C
1778009930	13.35 Volt	40 Pcnt	12.5 C
1778009330	13.35 Volt	28 Pcnt	12.5 C
1778008730	13.43 Volt	22 Pcnt	12.5 C
1778008130	13.5 Volt	27 Pcnt	13 C
1778007530	13.73 Volt	30 Pcnt	13 C
1778006930	14.18 Volt	20 Pcnt	13 C
1778006330	14.48 Volt	17 Pcnt	13 C
1778005730	14.48 Volt	16 Pcnt	13.5 C
1778005130	14.48 Volt	22 Pcnt	13.5 C
1778004530	14.48 Volt	22 Pcnt	13.5 C
1778003930	14.48 Volt	27 Pcnt	13.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Digi1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)